Motorola SB5101 all connected yet no internet

[princemakrani]

Hi guys,

I've got SB5101e I believe with Haxorware 1.1 R39. Had a problem yesterday and after trying few different mcs got connected with all the lights up on the modem, yet cannot access internet. what's this all about? does any one have any idea? At one point I had send/receive both lights blinking together, which I have not seen before, since normally they blink one by one and go online.

My existing settings:
factory mode
Force network access
disable updates
ALL TICKED with DHCP server running

Frequency as per B'ham 331, 339 and 425mhz
BPI Docsis 1.0


I need your help ASAP guys please. I've been trying to sort this out for hours now. In the light of the above:

why is this the case with lights all online yet no access?
what do I need to do to resolve this?
what settings do I need to change?
Do I need to spoof vendor info etc.?


Thank you in advance for your help guys.

Cheers.

[fnr3master]

ur using the wrong macs look at the config file size on the overview page near the bottom you want it in the 400's if it reads say 392 then all ur lights will go solid and it will even say operational but u wont be able to surf.

[princemakrani]

Originally Posted by fnr3master

ur using the wrong macs look at the config file size on the overview page near the bottom you want it in the 400's if it reads say 392 then all ur lights will go solid and it will even say operational but u wont be able to surf.

Yes, it does say 392 bytes. I managed to get online with one but it went down after little bit and then the online light kept flashing and it will not go solid. I will try some more mc's. Any idea about what sort of settings etc. i should be using?

thanks for your advice.

[tomsta79]

change baseline in settings from docsis 1.0 to bpi+ (docsis) 1.1 then save ive been told is been hacked then try mac.s until you find working mac.s hope this helps only on haxoware

[richkez]

ive got the same problem mate i can try the macs is my 5100 with sigma on and the mac works but when i try the same macs in my 5100 with haxo 1.1 r39 it just wont go online

it says at the bottom of the page 428 bytes which is a 10 meg mac but no Internet access

the only time i can get this modem online is with a 1/4 meg mac 76 bytes

[tomsta79]

ok m8 in baseline change from docsis 1.0 to docsis 1.1 then save ive been told all the mac.s that are working start with 00:14 which are docsis 1.1....every other mac i try on 1.0 might come on then go off with in mins just keep trying each mac that starts with 00:14 might find other speeds am looking in to it all my self matey

[princemakrani]

Originally Posted by tomsta79

ok m8 in baseline change from docsis 1.0 to docsis 1.1 then save ive been told all the mac.s that are working start with 00:14 which are docsis 1.1....every other mac i try on 1.0 might come on then go off with in mins just keep trying each mac that starts with 00:14 might find other speeds am looking in to it all my self matey

Do you mean mcs starting with 00:14 will only accept BPI 1.1 and else BPI 1.0? I have tried to no avail.

I was connected with one for a few days but suddenly just went and the online light was blinking constantly and won't go online. I have tried others and the send/rcv lights flash together, don't know why.

BTW does the Coax has to be disconnected before changing mcs? Any help would be appreciated.

cheers

[richkez]

i followed the link in this post reflashed the modem and now its working again

Any idea why modems have went down

[funkyfones]

Originally Posted by richkez

ive got the same problem mate i can try the macs is my 5100 with sigma on and the mac works but when i try the same macs in my 5100 with haxo 1.1 r39 it just wont go online

it says at the bottom of the page 428 bytes which is a 10 meg mac but no Internet access

the only time i can get this modem online is with a 1/4 meg mac 76 bytes

If it gives you a 428 byte config it works, dont touch the modem, reboot pc, also change nic mac on router/pc whichever is connected to modem and retry, also right click your connection and do 'repair' that clears cache etc

Originally Posted by princemakrani

BTW does the Coax has to be disconnected before changing mcs
cheers

yes