How to Jtag a Black Eurovox

[dolphin]

I had 2 Max_V Black Eurovox die on me, I did'nt really want to return them to the seller as I would be posting overseas at a cost to myself and then I would have a time delay in getting replacements. Answer was to try and Jtag one of them to see if it could be done, if not then the postman was going to get an extra delivery.

Anyway I got them both working - after a bit of trial and error - see below for instructions:

Flash with Tsop file for Red Eurovox “V_MAX__RED_07”, this puts Version 1.20 on the box. Use DnUpMan to update this to the “02_07_07.bin” file.

There is a problem with the Jtag file which prevents the output being displayed using the Scart lead, it also has the TV output channel tuned to channel 170 and has a request to enter a PIN number before allowing access to the box, but we can get over that by following the instructions below.

1)Connect Eurovox to TV using TV/VCR aerial connection on back of box (marked No 9, page 2 of manual).
2)Plug Eurovox into mains and switch on.
3)Tune your TV into channel 170.
4)You will see a request to enter a PIN – use the master PIN 1004.
5)Enter Menu and go to ‘Config’.
6)Go to ‘Clear Data’.
7)Enter PIN – 1004
8)Go to ‘Factory Default’, click OK.
9)Click on your Symbol rate, either Symbolrate(6887) or Symbolrate(6952) and OK that.
10)Click OK when the warning comes up.
11)Exit and then load your ‘Channel File’.

That’s it your box is now back to life.

D

[wigertoods]

Tried this method on one box I had and it worked almost fine.
Got the box alive again but couldn't load the box with the critical update.
kept getting the message "this firmware is not fit for this box" so I'm stuck with the original firmware until the new tsop is released.
Not a total disaster as the box still works for now.

[Trog]

I haven't had to do any of this so I am not sure but the first thing that popped into my head wqhen reading about your problem getting the critical update onto your box is that you have set your black box up as a red box. The critical update doesn't work with the red box and is blocking an update.

Couldn't you after jtagging your box, try to update it with an older black box firmware such as the july firmware. This may re-establish your black boxes identity helping you to install the critical update.

[dolphin]

kept getting the message "this firmware is not fit for this box" so I'm stuck with the original firmware until the new tsop is released

Yeh me too, but hey something is better than nothing - hopefully when the Tsop file for the black box comes out I'll be able to Jtag it with that.

getting the critical update onto your box is that you have set your black box up as a red box. The critical update doesn't work with the red box and is blocking an update.

Couldn't you after jtagging your box, try to update it with an older black box firmware such as the july firmware. This may re-establish your black boxes identity helping you to install the critical update.

Tried all those methods, I have the July update on my box now 'Version 2.10' but I'll have to wait for the new Tsop file to bring it back to a real Black box.

D

[wigertoods]

Yeah trog i'm sure that's the reason but as dolphin says
anything is better than a big doorstop at the moment.
can always re jtag again anyway.

[Burksninja]

but most tvs dont go to 170 so how do u tune it 2 170

[jonnie22265]

black v 2008 tsop here you go m82008TSOP.zip

[Burksninja]

nice 1

[barley]

cheers thanks a million!

[mrcool238]

Originally Posted by dolphin

I had 2 Max_V Black Eurovox die on me, I did'nt really want to return them to the seller as I would be posting overseas at a cost to myself and then I would have a time delay in getting replacements. Answer was to try and Jtag one of them to see if it could be done, if not then the postman was going to get an extra delivery.

Anyway I got them both working - after a bit of trial and error - see below for instructions:

Flash with Tsop file for Red Eurovox “V_MAX__RED_07”, this puts Version 1.20 on the box. Use DnUpMan to update this to the “02_07_07.bin” file.

There is a problem with the Jtag file which prevents the output being displayed using the Scart lead, it also has the TV output channel tuned to channel 170 and has a request to enter a PIN number before allowing access to the box, but we can get over that by following the instructions below.

1)Connect Eurovox to TV using TV/VCR aerial connection on back of box (marked No 9, page 2 of manual).
2)Plug Eurovox into mains and switch on.
3)Tune your TV into channel 170.
4)You will see a request to enter a PIN – use the master PIN 1004.
5)Enter Menu and go to ‘Config’.
6)Go to ‘Clear Data’.
7)Enter PIN – 1004
8)Go to ‘Factory Default’, click OK.
9)Click on your Symbol rate, either Symbolrate(6887) or Symbolrate(6952) and OK that.
10)Click OK when the warning comes up.
11)Exit and then load your ‘Channel File’.

That’s it your box is now back to life.

D

hello m8 i have same problem with my eurovox display stuck on 0001 all i get through scart socket is black screen and my tv only goes up to channel 70 so how do i get to tune tv to 170 please any help as its racking my brain
thanks