Go Back   Techwatch Support Forums: Digital & Satellite TV, FTA, Cable, Computers, Mobile Phones, Apple and General Tech Forums > Tech Forums > Satellite TV > Satellite Help



Satellite Help Anything satellite related

Reply
 
LinkBack Thread Tools
Old 11-08-07, 11:56 AM   #1 (permalink)
Junior Member
 
Join Date: Aug 2007
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Default Monobloc--Help needed

I'm a novice at this game,(Although I am getting on a bit)---I have a Metronic monobloc--(2 LNB's) linked to my 80 cm dish. If I line up the Primary LNB on Astra 19
I get a good Signal --70%--and loads of channels--But no signal from Hotbird.

If I line up the Primary LNB onto Hotbird 13 (AS recommended) I get signals from both LNB's but the Quality is very Low --30/35%--and can only get a few channels on each Satellite.

Help needed please

Ian
TOMMO7 is offline   Reply With Quote
Old 11-08-07, 12:09 PM   #2 (permalink)
Retired Mod & Sat Guru
 
nanochickin's Avatar
 
Join Date: Aug 2006
Location: Wolverhampton
Posts: 3,825
Thanks: 46
Thanked 338 Times in 270 Posts
Default Re: Monobloc--Help needed

:welc3: to the forum mate

As daft as it may sound have you got the monoblock the rightway up with the wire connecting at the bottom of the lnb

You also need to remember if the main focus is on Hotbird the lnb part that is needed for Astra 1 needs to be on the right side of the centre mounting point (i.e to the west not the east) if looking from the back of the dish. As daft as it may sound you can still get a signal showing even though your not looking at the correct satellite

It works like a mirror effect when fitting more than one lnb. (The monoblock is effectively 2 lnbs spaced 6 degrees apart with an inbuild DISEqC switch) The lnb will be on the opposite side from what you would expect it to be :?

Hope this helps



Nano

__________________
Sanity is nothing more than an excuse to be boring
nanochickin is offline   Reply With Quote
Old 11-08-07, 05:22 PM   #3 (permalink)
Dodgy Geezer
 
BGonaSTICK's Avatar
 
Join Date: Nov 2005
Location: Brighton
Posts: 9,718
Thanks: 3
Thanked 166 Times in 60 Posts
Default Poor quality readings

Some simple things to look at to improve signal quality readings.
These are in a very rough order of most-likely/beneficial/common down to odd/bizarre/unlikely/minor

-- Overall dish alignment not as it should be
-- Dish size too small
-- Incorrect LNB skew setting
-- LNB not at focal point of the dish due to
---- LNB too far forward in LNB clamp
---- LNB too far back in LNB clamp
---- LNB support arm bent or mal-aligned/fitted
-- Warped, damaged, dirty or poorly refinished dish face
-- Obstruction, or partial obstruction to line of sight (trees, buildings etc. etc.)
-- Old/failing LNB
-- Out of recognised satellite footprint
-- Poor quality coax/local interference
-- Unsuitable LNB for dish (mainly on either very large or small dishes or Sky/Non-Sky incompatibilities)
-- Damaged LNB (water ingress, spider's new home, heat damage, impact damage)
-- Incorrect feedhorn fitted (C120-type LNB)
-- Poor F connectors/fitting, though this usually has a very significant overall effect on operation

STICK
__________________
Dreambox 7000, Skystar2 PCI, Skystar USB, Fibo 90cm on Moteck SG2100, Triax TD110 multi-LNB. Sky + ART cards. 45.0°E - 58.0°W
BGonaSTICK is offline   Reply With Quote
Old 11-08-07, 09:34 PM   #4 (permalink)
Satellite Help member
 
Join Date: Nov 2006
Location: Suffolk, ENGLAND
Posts: 166
Thanks: 2
Thanked 7 Times in 7 Posts
Default Re: Monobloc--Help needed

Just a couple of pics of the set up I did for my daughter (Yes I have posted them on other boards also).
The clamped LNB is lined up on 13east (Hotbird), the offset LNB pics up 19east. 80cm dish in Ilford Essex.
BH
BlackHawk is offline   Reply With Quote
Old 12-08-07, 12:18 PM   #5 (permalink)
Junior Member
 
Join Date: Aug 2007
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Default Re: Monobloc--Help needed

Thanks for the Advice guys. The Monobloc seems to be fitted the correct way round. I'll just have to experiment with the Dish Direction fine tuning a bit.--I'll let you know how I go on.

Cheers Ian (TOMMO7)
TOMMO7 is offline   Reply With Quote
Old 12-08-07, 05:18 PM   #6 (permalink)
Super Moderator
 
Jimdefruit's Avatar
 
Join Date: Jan 2006
Posts: 2,858
Thanks: 20
Thanked 221 Times in 187 Posts
Default Re: Monobloc--Help needed

Welcome to the forum TOMMO7

Dont forget that the sat at 19.2E is a tad lower in the sky than the sat at 13E so you probably need to tilt the monoblock an itsy witsy bit for a good signal on both.
__________________
Dreambox 800 HD; Dreambox 7000s + VBox + Channel Master 1.2 with 36v actuator CM120 feedhorn and Invacom .3 LNB
Skystar 2 PCI card with links to my Dreamboxes

If you like what you see here, tell your friends.
Jimdefruit is offline   Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT +1. The time now is 01:27 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0 ©2011, Crawlability, Inc.