Patching your Technomate 1000 series - Page 2 - Techwatch: Satellite TV forums, FTA, Cable, Hardware, & Tech forums

bigtee · 21-06-08, 12:26 PM

You also need to load Kempa's Softcam which you'll find in the same place you got the patch. Loading softcam is similar (but using 'keys' tab of Loader) but simpler/quicker than loading patch.

ETA Also, did you load very latest patch i.e. 272 of 20-06-08?

redcharles · 21-06-08, 01:26 PM

Quote:

Originally Posted by bigtee

You also need to load Kempa's Softcam which you'll find in the same place you got the patch. Loading softcam is similar (but using 'keys' tab of Loader) but simpler/quicker than loading patch.

ETA Also, did you load very latest patch i.e. 272 of 20-06-08?

Thanks forthe help but now i really stuck dident find softcam keys with patch
and when i googled it came up as acd file and i carnt open it
redcharles

bigtee · 21-06-08, 03:42 PM

No no, don't just google; I assumed you got the Magic patch at Alsat forum. Google Alsat forum; you will then have to register; then go to the Technomate section - look for software - look for Kempa softcam - download - load to receiver. (Bob should then be ya father's brother).

redcharles · 21-06-08, 05:51 PM

I dont know what i have done now i canget darkman loader on screen but it when i press connect it says carnt open file
any help would be welcome
to a newbie
redcharles

737tx · 21-06-08, 07:16 PM

Hi Folks
this is my CHECK LIST when patching TM1000D

1 If not using a scart connection - check your system settings and note the rf output/Usals settings etc so you can reset it later

2 Now save your channel list from the box to your pc with the latest Darkman loader

3 Now do a factory reset , then go to standby and back on again

4 Now load the latest official firmware for the 1000d from www.technomate.com

5 Reboot = Go to standby and back on again

6 Now load the latest darkman patch for the 1000d from
_http://www.alsat.co.uk

7 Next load your saved channel list

8 Then load the latest tm softcam (usually by kempa82)
_http://www.alsat.co.uk

9 If you are not using a scart connection then change the rf channel from the default to the one you noted earlier, also remembering to update Usals if using that setup.

10 Do a final reboot (On/Off) just to be sure its all embedded ok

Hope this helps.

bigtee · 21-06-08, 07:38 PM

OK: the patches and softcams are in a compressed format; you have to un/decompress them first.

One of two programming formats are used by the Alsat folk for compression: either winzip or winrar. You have to download either of them to your computer and then use it to 'unzip' or 'unrar' any data compressed with the respective one before then using them (e.g. using loader to load them to receiver).

I believe that you should be able to download winrar from Alsat; otherwise search the NET for a possible free download.

redcharles · 23-06-08, 04:40 PM

Thanks for your help
I dont think i am computer savey enough will have to get help from mate
thanks anyway

redcharles

goalscorer29 · 26-08-08, 11:35 PM

where can i download darkman and the D+ Au 1000 series PATCH i cannot find any of them

Mickha · 27-08-08, 12:26 AM

You will no longer find a patch which offers D+ AU, as they upgraded their encryption and so is no longer open.
On alsat you will find Technomate patches by Magic, who took over from Darkman, which will open Premiere 19E, Polsat 13E, and Digi TV 1W, as well as other channels.

21-06-08, 12:26 PM	#11 (permalink)
bigtee Senior Member Join Date: Oct 2006 Location: Kent Posts: 431 Thanks: 7 Thanked 34 Times in 34 Posts	Re: Patching your Technomate 1000 series You also need to load Kempa's Softcam which you'll find in the same place you got the patch. Loading softcam is similar (but using 'keys' tab of Loader) but simpler/quicker than loading patch. ETA Also, did you load very latest patch i.e. 272 of 20-06-08? __________________ Raven 90 multi for 1w, 7e, 13e, 16e & 19e; TM1500 looped into Analogue receiver; 1m Orbital on SG 2100 5e-34w; Fortec 5400 & Phoenix Apollo Receivers

21-06-08, 03:42 PM	#13 (permalink)
bigtee Senior Member Join Date: Oct 2006 Location: Kent Posts: 431 Thanks: 7 Thanked 34 Times in 34 Posts	Re: Patching your Technomate 1000 series No no, don't just google; I assumed you got the Magic patch at Alsat forum. Google Alsat forum; you will then have to register; then go to the Technomate section - look for software - look for Kempa softcam - download - load to receiver. (Bob should then be ya father's brother). __________________ Raven 90 multi for 1w, 7e, 13e, 16e & 19e; TM1500 looped into Analogue receiver; 1m Orbital on SG 2100 5e-34w; Fortec 5400 & Phoenix Apollo Receivers

21-06-08, 05:51 PM	#14 (permalink)
redcharles Junior Member Join Date: Jun 2008 Posts: 10 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Patching your Technomate 1000 series I dont know what i have done now i canget darkman loader on screen but it when i press connect it says carnt open file any help would be welcome to a newbie redcharles

21-06-08, 07:16 PM	#15 (permalink)
737tx Junior Member Join Date: Jun 2008 Posts: 1 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Patching your Technomate 1000 series Hi Folks this is my CHECK LIST when patching TM1000D 1 If not using a scart connection - check your system settings and note the rf output/Usals settings etc so you can reset it later 2 Now save your channel list from the box to your pc with the latest Darkman loader 3 Now do a factory reset , then go to standby and back on again 4 Now load the latest official firmware for the 1000d from www.technomate.com 5 Reboot = Go to standby and back on again 6 Now load the latest darkman patch for the 1000d from _http://www.alsat.co.uk 7 Next load your saved channel list 8 Then load the latest tm softcam (usually by kempa82) _http://www.alsat.co.uk 9 If you are not using a scart connection then change the rf channel from the default to the one you noted earlier, also remembering to update Usals if using that setup. 10 Do a final reboot (On/Off) just to be sure its all embedded ok Hope this helps. Last edited by robbo71; 27-07-08 at 10:36 PM. Reason: De-activated Live links

21-06-08, 07:38 PM	#16 (permalink)
bigtee Senior Member Join Date: Oct 2006 Location: Kent Posts: 431 Thanks: 7 Thanked 34 Times in 34 Posts	Re: Patching your Technomate 1000 series OK: the patches and softcams are in a compressed format; you have to un/decompress them first. One of two programming formats are used by the Alsat folk for compression: either winzip or winrar. You have to download either of them to your computer and then use it to 'unzip' or 'unrar' any data compressed with the respective one before then using them (e.g. using loader to load them to receiver). I believe that you should be able to download winrar from Alsat; otherwise search the NET for a possible free download. __________________ Raven 90 multi for 1w, 7e, 13e, 16e & 19e; TM1500 looped into Analogue receiver; 1m Orbital on SG 2100 5e-34w; Fortec 5400 & Phoenix Apollo Receivers


Technology Forums: FTA, Satellite, Cable, Home Media, Hardware & Computers \| Home \| Forums \| News \| Blog \|

23-06-08, 04:40 PM	#17 (permalink)
redcharles Junior Member Join Date: Jun 2008 Posts: 10 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Patching your Technomate 1000 series Thanks for your help I dont think i am computer savey enough will have to get help from mate thanks anyway redcharles

26-08-08, 11:35 PM	#18 (permalink)
goalscorer29 Junior Member Join Date: Aug 2008 Posts: 2 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Patching your Technomate 1000 series where can i download darkman and the D+ Au 1000 series PATCH i cannot find any of them

27-08-08, 12:26 AM	#19 (permalink)
Mickha Super Moderator Join Date: Feb 2006 Posts: 1,341 Thanks: 3 Thanked 142 Times in 127 Posts	Re: Patching your Technomate 1000 series You will no longer find a patch which offers D+ AU, as they upgraded their encryption and so is no longer open. On alsat you will find Technomate patches by Magic, who took over from Darkman, which will open Premiere 19E, Polsat 13E, and Digi TV 1W, as well as other channels.