nube talk back - Techwatch Support Forums: Digital & Satellite TV, FTA, Cable, Computers, Mobile Phones, Apple and General Tech Forums

screem · 26-02-08, 02:39 PM

i have a pace di4001n and i have read the NoviceAngel Cable Guide Pace
(very good) but the photo of wear you cut the talk back is a bit crap
i can not make out wear it is.I asoom it is in the tuner wear the cable wire go's in but i have 2 tuner togerth at right angles joining it can any one please help a nube

jimbo · 26-02-08, 03:52 PM

its the one the cable goes into, undo the cable take the silver hexagon nut of look down the side of the tuner for a small starhead screw, remove it then lever the tuner from side to side gently, its got about 25 pins or so at the bottom near the board, u may have to break a little solder at the top plate were it joins the 2 tuners, remove and take the side of then u will see the link, u can just lift a leg of the chip.

screem · 26-02-08, 04:25 PM

Great thanx found it and done it now i will have to read up on the rest of the chipping process

screem · 26-02-08, 04:57 PM

just tested the pace box all i get is a black sceen and message saying tune on the front

Alessandro · 26-02-08, 09:58 PM

I will definitely have to get into this stuff

reddiesel · 27-02-08, 01:59 AM

Quote:

Originally Posted by screem

just tested the pace box all i get is a black sceen and message saying tune on the front

I hope your in pure ntl area as 4001 only works there, take lid off and next to the battery is a small red jumper, with box switched off pull jumper off for a few minutes then replace, then power box up with cable connected and it will update and set net id, then power off and back on holding up and down buttons in till it says diag on display and your in eng menu, set pin and frequency,power off then on and you should have freeview channels, then put programmed card in.

screem · 27-02-08, 12:07 PM

thanx but still a blank black screen yes i am in a ntl area(now virgin)

reddiesel · 28-02-08, 01:17 AM

Quote:

Originally Posted by screem

thanx but still a blank black screen yes i am in a ntl area(now virgin)

Read the stuck in tune guide.

screem · 28-02-08, 01:20 AM

thanx i will give it a go

screem · 28-02-08, 07:41 PM

no it did not work i must have done something wrong thanx anyway

26-02-08, 02:39 PM	#1 (permalink)
screem Junior Member Join Date: Jan 2008 Posts: 15 Thanks: 0 Thanked 0 Times in 0 Posts	nube talk back i have a pace di4001n and i have read the NoviceAngel Cable Guide Pace (very good) but the photo of wear you cut the talk back is a bit crap i can not make out wear it is.I asoom it is in the tuner wear the cable wire go's in but i have 2 tuner togerth at right angles joining it can any one please help a nube

26-02-08, 03:52 PM	#2 (permalink)
jimbo Super Moderator Join Date: Aug 2007 Posts: 3,773 Thanks: 254 Thanked 891 Times in 554 Posts	Re: nube talk back its the one the cable goes into, undo the cable take the silver hexagon nut of look down the side of the tuner for a small starhead screw, remove it then lever the tuner from side to side gently, its got about 25 pins or so at the bottom near the board, u may have to break a little solder at the top plate were it joins the 2 tuners, remove and take the side of then u will see the link, u can just lift a leg of the chip. __________________ i now keep copies of some posts before they are deleted, this is a private matter.

26-02-08, 04:25 PM	#3 (permalink)
screem Junior Member Join Date: Jan 2008 Posts: 15 Thanks: 0 Thanked 0 Times in 0 Posts	Re: nube talk back Great thanx found it and done it now i will have to read up on the rest of the chipping process

26-02-08, 04:57 PM	#4 (permalink)
screem Junior Member Join Date: Jan 2008 Posts: 15 Thanks: 0 Thanked 0 Times in 0 Posts	Re: nube talk back just tested the pace box all i get is a black sceen and message saying tune on the front

26-02-08, 09:58 PM	#5 (permalink)
Alessandro Junior Member Join Date: Feb 2008 Posts: 6 Thanks: 0 Thanked 0 Times in 0 Posts	Re: nube talk back I will definitely have to get into this stuff

27-02-08, 12:07 PM	#7 (permalink)
screem Junior Member Join Date: Jan 2008 Posts: 15 Thanks: 0 Thanked 0 Times in 0 Posts	Re: nube talk back thanx but still a blank black screen yes i am in a ntl area(now virgin)

28-02-08, 01:20 AM	#9 (permalink)
screem Junior Member Join Date: Jan 2008 Posts: 15 Thanks: 0 Thanked 0 Times in 0 Posts	Re: nube talk back thanx i will give it a go

28-02-08, 07:41 PM	#10 (permalink)
screem Junior Member Join Date: Jan 2008 Posts: 15 Thanks: 0 Thanked 0 Times in 0 Posts	Re: nube talk back no it did not work i must have done something wrong thanx anyway

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Just got my new Eurovoxv max back	darkpsyde	Eurovox	1	08-02-08 04:08 PM
can you get box office with samsung 2100c without re-connecting talk back	skelly82	Cable TV Chat	11	09-12-07 04:20 PM
Shuttle moves back to the launch pad	BGonaSTICK	The Lounge	0	15-05-07 04:08 PM
Talk Back	5av1dg312	Cable TV Chat	2	23-04-07 12:13 PM
im back :D	maverick_15	Introduce yourself	8	30-09-05 06:20 PM