Tiny Unlooper help ( Baffled )

[Roco]

Hi , i hate seeing HELP in posts but i feel it was my turn to use this,

Got my tiny this morning thinking all i had to do was connect it & run bodunlocker script. I need to unlock a rom11bod but iv got a spare rom11bod which i will practice on first

apparently my pot setting is 55 ohms for a Vcc floor to ceiling of around 1a-1b for a rom10. So i will need to ajust the pot first using VccAnalyser.

I double click on "VCC Analyzer v3" & winexplorer v5.0 opens.
I pick Unlooper under parameters settings
I hit exicute & get the following



Executing Script: C:\Documents and Settings\roco\Desktop\WinExpl5.0\VCC Analyzer v3.xvb
TX Data : 02 03 00
TX Data : 02 02 00
TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 02 00
TX Data : 12 15 AB 21 00 08 A0 CA 00 00 02 12 00 06 55 0E
03 8B 00
RX Data : 02 00

VCC 30: ??????

Sc.Read: Timeout Reading Data From Card - 5 Bytes Requested, 4 Bytes Read, Continuing Script
??

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script
XXXX 6F = 0% FF = 0%
VCC 2F: ??XX???????? 6F = 0% FF = 0%
VCC 2E: XX??XXXXXX?? 6F = 0% FF = 0%
VCC 2D: ??

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 1 Bytes Read, Continuing Script

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script


Script Error on Line 79
Sc.GetByte: Requested Byte Exceeds Last Read Request



any help guys , what am i at ,lol

[sqwidge]

looks like your pot is set to 30 on a t911 i have mine set to 20 but not sure for the tiny, are you getting the minus and plus sign (-----+---+----)when its attempting to read your card? My bad you would only get this in sidewinder!!

[Roco]

the stuff i posted above is all i get, no - or + , this is my spare card by the way.
I have a sammy 2110 card which i dont want to mess with untill i know what im at

apparantly i need a floor to ceiling of about 22 - 27

[Roco]

right before i run script it say in the window in top right ;
"For ROM 1 select 74HC4053 and adjust Vcc to around 26 as a starting point"

I think it means rom11, anyway how do i select 74HC4053?

[Roco]

im getting there , not easy getting this pot right though

[morashid679]

Originally Posted by Roco

im getting there , not easy getting this pot right though

Turn your pot setting screw all the way clockwise till it clicks and then turn it back 5 turns then run vcc analyzer you should get a better reading.

Turn the screw both ways clock and anti all the way to check for right reading.

[ImSm0kin1]

alright mate

i have one of these tiny unloopers, they will pop a rom11 in no time, ive even done a couple of rom10 A86 cards on mine.

here, were you say "For ROM 1 select 74HC4053 and adjust Vcc to around 26 as a starting point", that means swap the chips round to the extra set that you should have got with the unlooper (i think it is supposed to say ROM11 not ROM1).

if its like mine and came preinstalled with the 74HCT4053 chips then it should pop rom11s no problems anyway, so no need to swap chips around.

have you installed the windows script control on your PC ? if not your going to need to download and install it, then load up winexplorer 5.4 and drop your vcc analyser script into it.

once you run the script adjust screw clockwise untill you see a line of -------------- with no +++ at the vcc required, in your case you should be seeing this ....

VCC 28---+---+++----++-+----
VCC 27-----++----+---+-----+-
VCC 26 ------------------------ < this is what you want to see.

once you've done that, load up your unlocking script and it should pop within five mins.

one more thing mate, before i adjust the pot screw, i always switch off the power to the unlooper. i dunno why, i read it somewhere i think, but i havent killed a card since ive been doing this.

hope that helps ya a bit mate, cos i know how frustrating they are to get running properly.

[Roco]

thanks guys for the info, just taking it all in. I'll post my results shortly,things are becoming alittle more clearer

[Roco]

alright guys , right i cant get winex 5.4 working as under the program parameters there is no option for UNLOOPER ? so i tried on winexplorer 5.0

I installed script controll
I turned screw clockwise untill it clicked & the 5 full turns back
I loaded up vvc-analyzer v3
I put card in unlooper & added power
I hit execute script

heres what i get , i just need to ajust the screw now?


Executing Script: C:\Users\roco\Desktop\WinExpl5.0\mick data tiny files\VCC Analyzer v3.xvb
TX Data : 02 03 00
TX Data : 02 02 00
TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 02 00
TX Data : 12 15 AB 21 00 08 A0 CA 00 00 02 12 00 06 55 0E
03 8B 00
RX Data : 02 00

VCC 30: ???????????? 6F = 0% FF = 0%
VCC 2F: ------????-- 6F = 0% FF = 67%
VCC 2E: XXXX--??XXXX 6F = 0% FF = 17%
VCC 2D: XXXXXX--??-- 6F = 0% FF = 33%
VCC 2C: ----????XXXX 6F = 0% FF = 33%
VCC 2B: XXXXXXXXXX?? 6F = 0% FF = 0%
VCC 2A: --??XXXXXX?? 6F = 0% FF = 17%
VCC 29: XX????XX???? 6F = 0% FF = 0%
VCC 28: XXXX??XX???? 6F = 0% FF = 0%
VCC 27: ????

Sc.Read: Timeout Reading Data From Card - 5 Bytes Requested, 3 Bytes Read, Continuing Script

Script Error on Line 82
Sc.GetByte: Requested Byte Exceeds Last Read Request

[ImSm0kin1]

download this ini file mate, and drop it into the same folder as winexplorer 5.4.

then open winexplorer and select ' MY LOOPER ' from the program parameters.

hopefully then you'll be up and running.

_http://www.mediafire.com/?sharekey=ce9cb5890f668365d2db6fb9a8902bda

(remove the underscore from the start of the link)