haxoware sb5101e

[reptilianman]

Hi everyone can anyone explain a few settings in the config menus as im not sure what they do or refer to i have a good idea well actually am pritty sure but need to know bear with me some of its really straight forward but i need to know. thanx

1. Settings menu: what does the following mean and do!

Force network access?
TFTP enforce bypass?
Disable IP filters?

2. Config menu: what does the following mean and do!

Auto serve enabled?
then you can upload a downloaded config that you get from there server i belive?

thanx for the help.

[racky29]

have a look at the haxorware manual
its for 092, but you can get a good idea of most settings

http://www.mediafire.com/?djzjg4udwby

[reptilianman]

thanx racky29

[steveo__]

Hi guys...

new to Haxoware - but have benn told to look it up and flash my modem

Couple of questions....

where do I get the Haxoware software from and is it easy to do?

Thanx

[princemakrani]

you can download it from here m8

sbhacker.net/forum/Firmware-Haxorware-10r-t6433.html&hl=haxorware+download


hope it helps.

[metalpunk]

Originally Posted by steveo__

Hi guys...

new to Haxoware - but have benn told to look it up and flash my modem

Couple of questions....

where do I get the Haxoware software from and is it easy to do?

Thanx

Best to read the manuals a couple a times m8t...

[Bad_Ad84]

Originally Posted by reptilianman

1. Settings menu: what does the following mean and do!

Force network access?
TFTP enforce bypass?
Disable IP filters?

Force network access, not required in the UK
TFTP Enforce, not required in the UK
Disable IP Filters, allows snmp scanning, also not required in the UK.

Originally Posted by reptilianman

Auto serve enabled?

Lets you serve a config from the modem, rather than downloading from TFTP, also not required.

[steveo__]

any links to the mnauals please?

[666]

Haxorware Settings
----------------------
Configuration:
---------------------
Settings-
General:
Factory Mode - Unticked
Disable Firmware Upgrades - Ticked
Force Network Access - Ticked
Tftp Enforce Bypass - Ticked
Disable IP Filters on Startup - Unticked
Current IP Filters Status - Optimized
Administration:
Control Panel IP Address - 192.168.100.1
DHCP Server - Ticked
Telnet Server - Unticked
Username - Root
Password - Admin
Frequency Settings:
Annex - Both
Plan - European
Preferred DS Freq 1 - 402750000 (this is for NTL, TW and others are different)
2 and 3 - 0
Upstream channel - dont change (will change on its own)
Addresses:
HFC MAC - Your Mac Address
Ethernet Mac - Dont touch
USB MAC - Copy your HFC MAC address, only this time change the last letter/number on it to 1 letter/number higher.
Serial Number - Dont Touch
Config File:
Server IP: Put whatever your server IP address you are using here, you can get it from DHCPforce.
Filename: Whastever you wish for your filename to use, if you want to force the 20mb option, then use - cmreg-ntlhm250-bund03.cm for NTL area, once again TW etc will be different.
Autoserve Enabled - Unticked
Stored cfg/store new config - no need to do anything here.
Baseline Privacy:
BPI - Disabled
Certificate - BPI Public Key
All the rest in the Baseline privacy section will not be touched.
And that is that, that should be everything done and you should now be able to get online.

[metalpunk]

Originally Posted by steveo__

any links to the mnauals please?

You need to go to Private fta section......lincsats post.....its all in there
Seek and you shall find !