VCC 30: XXXXXXXXXXXX - Why does this happen some cards with ATR

[Roco]

Good morning all , just curious if anyone know how to sort this problem out. Iv read loads of threads whit people haveing this problem but i havent found any solution to it if there even is one.

Tiny unlooper
Card has a ATR in Nagraedit but when run VCC-Analyzer I get :

VCC 30: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2F: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2E: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2D: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2C: XXXXXXXXXXXX 6F = 0% FF = 0%
ect
ect
ect
VCC Ceiling: 00
VCC Floor..: 00

Iv had a few cards like this now,they have a ATR but i still get the above.
No matter how much i change the pot i still get nothing.
i can do other cards fine.

any ideas?

i cant try anything this morning though,got some sh1t to do

cheers

[BL4K3Y]

What unlooper are you using?

[Roco]

TINY-UNLOOPER mate but iv seen others having this problem with other makes.
Im thinking the cards are just dead but i thought aslong as there is a ATR then it is ok. I feel confidant im doing everything correct so the problem must be with the card & i was just hoping someone knew a solution to the problem or is it only good for the bin.

good luck

[sharkbait559]

ive had that in past and if anyone knows the answer then im intrsted to find out.

[BL4K3Y]

Does the card read successfully in Nagra and does it have a provider etc?

[sqwidge]

Originally Posted by Roco

Good morning all , just curious if anyone know how to sort this problem out. Iv read loads of threads whit people haveing this problem but i havent found any solution to it if there even is one.

Tiny unlooper
Card has a ATR in Nagraedit but when run VCC-Analyzer I get :

VCC 30: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2F: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2E: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2D: XXXXXXXXXXXX 6F = 0% FF = 0%
VCC 2C: XXXXXXXXXXXX 6F = 0% FF = 0%
ect
ect
ect
VCC Ceiling: 00
VCC Floor..: 00

Iv had a few cards like this now,they have a ATR but i still get the above.
No matter how much i change the pot i still get nothing.
i can do other cards fine.

any ideas?

i cant try anything this morning though,got some sh1t to do

cheers

The only time i have ever seen similar to this is when i run sidewinder and the vcc is too high i run mine around the 20 mark i know we have diff unloopers (im using the t911) but if its set too high then it wont read it properly, have you tried adjusting your pot?

[Roco]

sqwidge-yea mate,adjusting pot doesnt make a difference. i adjust it fine for other cards though.

blakey - yea mate it reads everything it should read for a locked card in nagra,atr,cam ect.


cheers

[ImSm0kin1]

did anyone ever figure this 1 out ?

a mate brought me a card earlier from a 2110, it reads in nagra as a rom11 B0D with a valid cam id and provider info and all that stuff.

if i open it in mrom and click reset it gives an IRD beginning 3E so im pretty sure it hasnt been hit with 6D boxkey yet.

when i fire up the TINY to unloop the fecker i get the exact same result as the OP

anyone know a way around this ?

[reddiesel]

The only time i use vcc is if i have a rom 10 or use a different script, i dont reset with every card, i never have a problem popping bod's with M/D script, have you tried running the script with setting that worked on another bod ?

[spikebaby]

use the mikedata rom bod A86 script, and flash the tiny with the tiny flash, i reckon you are using the sidewinder script, yyou should not have any problems with the above script