Haxorware ip address issues

[chrisnasah]

Hi Guys,

I have always been using infinte but just testing haxorware, just got stuck with a weired issue. For some reason when my modem is connected to PC it does not seem to get an ip address. If i fix the IP address i.e. 192.168.100.10 i can access 192.168.100.1 and can also see the modem is online got a config etc but for some reason my PC is failing to get an ip address.

Any ideas? Is it anything to do with the section of mac address, had HFC address, ethernet mac address and usb mac address, does ethernet mac address need to be the same as my pc ethernet mac address?

Thanks

[5av1dg312]

not using that firmware myself and havent yet tryed it but theres nothing on it to do with getting i.p dynamic is there?

[chrisnasah]

not sure could not see it anywhere. Is there a guide on haxorware as there are so many options to configure etc which does not explain what they are or what they do.

Honest opinion, this haxorware might be useful for a expert on modems and know what all this options etc do.

I have been using infinite and its simple as in flash it and do the cmmands needed to protect it and away you go. Been struggling with this haxorware since dont know how many hours and just given up, maybe its a touch and go?? dont know. It just got too many options to configure where as someone like me jst wanna go online.

just dont know why i cant get an ip address... put me off it infinite rocks i guess

[ste0ey]

thanks to whoever wrote this origonaly, ive put the rest of freqs in and taken out the forced config part.

Haxorware Settings
----------------------
Configuration:
---------------------
Settings-
General:
Factory Mode - Unticked
Disable Firmware Upgrades - Ticked
Force Network Access - Ticked
Tftp Enforce Bypass - Ticked
Disable IP Filters on Startup - Unticked
Current IP Filters Status - Optimized
Administration:
Control Panel IP Address - 192.168.100.1
DHCP Server - Ticked
Telnet Server - Unticked
Username - Root
Password - Admin
Frequency Settings:
Annex - Both
Plan - European
Preferred DS Freq 1 - 402750000 (this is for NTL) (TW are 331000000 or 339000000)C&W frequency - 586750000
2 and 3 - 0
Upstream channel - dont change (will change on its own)
Addresses:
HFC MAC - Your Mac Address
Ethernet Mac - Dont touch
USB MAC - Copy your HFC MAC address, only this time change the last letter/number on it to 1 letter/number higher.
Serial Number - Dont Touch
Baseline Privacy:
BPI - Disabled
Certificate - BPI Public Key
All the rest in the Baseline privacy section will not be touched.
And that is that, that should be everything done and you should now be able to get online.

[Bad_Ad84]

you dont need to change anything, its just defaults + your regions freq + mac.

[chrisnasah]

Thanks will give it another go tonight when i get home from work.

As i have done quite a few changes do i just reset the modem back to default and add the mac plus my frequency or shall i flash it again to get it back to default.

Thanks

[Bad_Ad84]

to flash you would need to do a 2mb dump to reset defaults, i wouldnt bother.

just do factory reset in haxorware, goto freq and change to "both and euro" then enter your regions freq.

save and reboot and you should see lights going solid as it locks, go back to haxorware again and sort out mac.

[chrisnasah]

Hi,

Just to add this modem was on Infinite and i flashed it with 2mb dump with RC3 i believe.

Once that was doen i flashed it again with RC6, just wondering whether this might have caused an issue.

Has anyone got a 2mb dump with RC6 which i might do as a last resort.

Thanks

[Bad_Ad84]

that should be fine.

[chrisnasah]

finally got it working dont know what i did but reflashed again 2mg and it was fine after that.