Pace Di2000 - Removing Atmels - Techwatch Support Forums: Digital & Satellite TV, FTA, Cable, Computers, Mobile Phones, Apple and General Tech Forums

G77 · 02-02-09, 02:26 PM

does anyone have a tut on where the bk is located in the atmels?

also, are both chips required to be lifted?

thanks in advance.

afcwomble · 02-02-09, 05:01 PM

You need to remove both-there's a part in each one. Use BKE2.2 to read the chips(use CHIP tab) putting left read dump in top box and right in bottom(in the AT49LV1614 boxes)-hit search and you should see BK & IRD. Make sure when you remove you don't mix them up. And I would do 1 at a time, remove right and read, then replace to see if OK. If it comes up 8888 on front you know it's a problem with that chip rather than guessing which 1. Then repeat with left. Good luck-i've only managed to get the buggers off & read-never had any luck in replacing and get working

G77 · 02-02-09, 05:26 PM

cheers r kid! looks like me dumps are corrupt thou. it says to clean legs ect so i guess im gonna do that for a bit

G77 · 02-02-09, 05:28 PM

bent the legs a little more and found the id button on the willem program. successfully got an ird begining with 12

bk looks goodish too.

now am i right in thinking that if i screw it up puitting them back in i can use the other set of pads and join the jumper?

afcwomble · 02-02-09, 06:40 PM

Glad you're getting there-Not too sure about that one about using the other pads-I think there was a way of doing this if need, don't know if it's ok for the 2000's.
Just make sure the pads are nicely cleaned-use a bit of wick and plenty of flux and clean with meths. Tack the atmel back on at end & check that its corectly aligned-it's a tricky operation so take your time-i've launched a couple across the room before

tdubman · 02-02-09, 11:51 PM

thats correct you can use the other pads short the link

02-02-09, 02:26 PM	#1 (permalink)
G77 Super Moderator Join Date: May 2008 Posts: 6,118 Thanks: 695 Thanked 1,250 Times in 1,044 Posts	Pace Di2000 - Removing Atmels does anyone have a tut on where the bk is located in the atmels? also, are both chips required to be lifted? thanks in advance. __________________ 1M Motorised Dish, 45W-36E, DM800HD. Quad LNB Mesh Mini Dish, 28.2E, DM500, TM500. Samsung Galaxy S GT-I9000 XXJVU & CF-Root.

02-02-09, 05:01 PM	#2 (permalink)
afcwomble Senior Member Join Date: May 2008 Posts: 358 Thanks: 15 Thanked 53 Times in 52 Posts	Re: Pace Di2000 - Removing Atmels You need to remove both-there's a part in each one. Use BKE2.2 to read the chips(use CHIP tab) putting left read dump in top box and right in bottom(in the AT49LV1614 boxes)-hit search and you should see BK & IRD. Make sure when you remove you don't mix them up. And I would do 1 at a time, remove right and read, then replace to see if OK. If it comes up 8888 on front you know it's a problem with that chip rather than guessing which 1. Then repeat with left. Good luck-i've only managed to get the buggers off & read-never had any luck in replacing and get working

02-02-09, 05:26 PM	#3 (permalink)
G77 Super Moderator Join Date: May 2008 Posts: 6,118 Thanks: 695 Thanked 1,250 Times in 1,044 Posts	Re: Pace Di2000 - Removing Atmels cheers r kid! looks like me dumps are corrupt thou. it says to clean legs ect so i guess im gonna do that for a bit __________________ 1M Motorised Dish, 45W-36E, DM800HD. Quad LNB Mesh Mini Dish, 28.2E, DM500, TM500. Samsung Galaxy S GT-I9000 XXJVU & CF-Root.

02-02-09, 05:28 PM	#4 (permalink)
G77 Super Moderator Join Date: May 2008 Posts: 6,118 Thanks: 695 Thanked 1,250 Times in 1,044 Posts	Re: Pace Di2000 - Removing Atmels bent the legs a little more and found the id button on the willem program. successfully got an ird begining with 12 bk looks goodish too. now am i right in thinking that if i screw it up puitting them back in i can use the other set of pads and join the jumper? __________________ 1M Motorised Dish, 45W-36E, DM800HD. Quad LNB Mesh Mini Dish, 28.2E, DM500, TM500. Samsung Galaxy S GT-I9000 XXJVU & CF-Root. Last edited by G77; 02-02-09 at 06:02 PM.

02-02-09, 06:40 PM	#5 (permalink)
afcwomble Senior Member Join Date: May 2008 Posts: 358 Thanks: 15 Thanked 53 Times in 52 Posts	Re: Pace Di2000 - Removing Atmels Glad you're getting there-Not too sure about that one about using the other pads-I think there was a way of doing this if need, don't know if it's ok for the 2000's. Just make sure the pads are nicely cleaned-use a bit of wick and plenty of flux and clean with meths. Tack the atmel back on at end & check that its corectly aligned-it's a tricky operation so take your time-i've launched a couple across the room before

02-02-09, 11:51 PM	#6 (permalink)
tdubman ipost what iknow not read Join Date: Jul 2008 Posts: 707 Thanks: 66 Thanked 129 Times in 110 Posts	Re: Pace Di2000 - Removing Atmels thats correct you can use the other pads short the link

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
pace di2000 voltmeter guide	n22bmw	Cable TV Chat	4	05-11-08 12:56 AM
Pace 4010	Thuggy	Cable TV Chat	6	19-09-08 11:22 PM
New Pace unit focuses on pay-TV innovations	BGonaSTICK	Satellite News	0	05-09-07 02:25 PM
Locked PACE DI400 1NC	JimmyGLew	Cable TV Chat	9	17-08-07 03:01 PM
pace di4001-n	jayjayw	Cable TV Chat	10	21-07-07 04:48 PM