tftp timeout

[mikeomz]

iam trying to put hax on my webstar with hyperterminal .ive got to the d option stage and set the tftp server as 10.128.135.171,put my firmware in the root directory of tftp32 and then all i get is tftp timeout.help me pleaeaess

[yusuf_gaz]

Hi

Shouldnt it be 192.168.100.10.

Regards

[lee-ds]

Originally Posted by mikeomz

iam trying to put hax on my webstar with hyperterminal .ive got to the d option stage and set the tftp server as 10.128.135.171,put my firmware in the root directory of tftp32 and then all i get is tftp timeout.help me pleaeaess

Where have you got that tftp server ip from?

[mikeomz]

i got it from the box in tftp32 .i know .am a doofus.i bought a max232 and ive been following the instructions i got with it, keep getting the tftp timeout
grrr.
cheers

[baked188]

Plug your modem in, give it 5 seconds, open tftp and it 'should' say 192.168.100.10.
Then turn modem off start hyperterminal/puttytel and plug ur modem back in.
Board ip:192.168.100.1 TFTP server ip: 192.168.100.10

If your still having problems try using Pumpkin tftp i find it the most reliable tftp program.

[mikeomz]

thanx cheers

that sounds like just what i was looking for.will give it a go, when i get in. and post back
cheers

[mikeomz]

ok.got all the tftp sorted .ive got to this stage

TFTP Get Selected

Board TFTP Server IP Address [10.128.135.171]: 192.168.100.10
Enter TFTP filename [haxorware11rev31]: haxorware11rev31.bin


Free store: a0500000
Starting TFTP of haxorware11rev31.bin from 192.168.100.10
Getting haxorware11rev31.bin using octet mode
.................................................. ..............................
.................................................. ..............................
.................................................. ..............................
.................................................. ..............................
.................................................. ..............................
.................................................. ..............................
.................................................. ..............................
.................
Tftp complete
Received 1182632 bytes
Image 0 Program Header:
Signature: 3349
Control: 0000
Major Rev: 0001
Minor Rev: 0001
Build Time: 2009/3/27 15:02:00 Z
File Length: 1182540 bytes
Load Address: 80500000
Filename: ecram_sto.bin
HCS: f886
CRC: d1e81540

WARNING: Signatures do not match! Don't use this image!

CRC Verified

Destination image
0 = bootloader
1/2 = CM image
3 = specify flash sector
(0-3)[2]:


is this warning usual,how do i proceed without brickin it

cheers

[sr20]

Originally Posted by mikeomz

<snip>...

is this warning usual,how do i proceed without brickin it

cheers

Enter 1 and once its stored the image, say no the the q store parameters to flash

sr20

[mikeomz]

cheers .can u repeat the end bit again,stor parameters to flash?? y? n?

cheerc

[mikeomz]

i didnt store the parameters to flash and got this.

0 = bootloader
1/2 = CM image
3 = specify flash sector
(0-3)[2]: 1
Are you sure you want to store an uncompressed image? [n] y
Stored 1182632 bytes
Verified 1182632 bytes
Store parameters to flash ? [n] n


Main Menu:
==========
d) Download and save to flash
g) Download and run from RAM
c) Store icePROM bootloader to flash
b) Boot from flash
e) Erase flash sector
m) Set mode
s) Store bootloader parameters to flash
i) Re-init ethernet
r) Read memory
w) Write memory

any next steps?have i done it right.