config file help

[m1n1_me]

hellp every one im looking for a list of gonfig file's but honest give up looking after about 6 hour's can any one help? all i need is the list so i cna download them with the downloader in haxor!

thankl's mark!!!!!!!!!

[chef1]

m8 the list of configs are on the stickies

tbh there is no force any more in most areas so your wating your time
best thing to do is keep trying macs and leave the conig and tftp blank
haxor will get them automatic if your upto date

you should have a good read through the forum m8
6 hours searching and you will find your answer

[sheeks]

i can still force in my area using a 2meg mac and forcing to 20 works flawless

[50pounds]

Tftp Server Addresses:

10.137.103.8
10.137.103.1
10.137.103.3
10.137.103.2
10.137.103.4
10.137.103.5
10.137.103.6
10.137.103.7
10.137.103.9


Config Files:

Ex NTL:
cmreg-mota4100-rts98.cm - 2MB down 256k up
cmreg-mota4100-bas.cm - 10MB down 512k up
cmreg-mota4100-rts22.cm - 20MB down 768k up
cmreg-ntlhm100-rts98.cm - 2MB down 256k up
cmreg-ntlhm100-bas.cm - 10MB down 512k up
cmreg-ntlhm100-rts22.cm - 20MB down 768k up
cmreg-ntlhm120-rts98.cm - 2MB down 256k up
cmreg-ntlhm120-bas.cm - 10MB down 512k up
cmreg-ntlhm120-rts22.cm - 20MB down 768k up
cmreg-ntlhm200-rts98.cm - 2MB down 256k up
cmreg-ntlhm200-bas.cm - 10MB down 512k up
cmreg-ntlhm200-rts22.cm - 20MB down 768k up
cmreg-ntlhm250-rts98.cm - 2MB down 256k up
cmreg-ntlhm250-bas.cm - 10MB down 512k up
cmreg-ntlhm250-rts22.cm - 20MB down 768k up

Ex Telewest:
cm-512-128 - 512k down - 128k up
cm-2148-256 - 2MB down - 256k up
cm-10240-512 - 10MB down - 512k up
cm-20480-768 - 20MB down - 768k up
stb-cpe2-1024-256 - 1MB down - 256k up - 2 IP's (???)
cm-cpe2-2148-256 - 2MB down - 256k up - 2 IP's
cm-cpe2-4096-384 - 4MB down - 384k up - 2 IP's
cm-cpe2-10240-512 - 10MB down 512k up - 2 IP's
cm-cpe2-20480-768 - 20MB down 768k up - 2 IP's
class-cm-rts01.cm - 20MB down 768k up

Any Network Configs:
cmbus-pkg1-nat-any.cm - 4MB Down 512k up
cmbus-pkg2-nat-any.cm - 10MB Down 769k up
cmbus-pkg3-nat-any.cm - 20mb Down 1mb up

Dyamic configs

A3b75f9a8e95f1e8c.cm -10mb
Adc3b1e1ca6266ca8.cm - 2mb
A0d1b8c927850ecfc.cm - 2mb
A0d1b8c927850ecfc.cm - 2mb
A7ddb0c5514a02917.cm - 10mb
A0d1b8c927850ecfc.cm - 2mb
A2ab87fa8b47e536a.cm - 10mb
A0d1b8c927850ecfc.cm - 2mb

These are the ones i have found from a few UBR's



But some areas are now dyamic and dont work forcing..

also as chef1 stated its at the top of forum as a sticky!

[cockneysean]

tbh there is no force any more in most areas

This is quite an untrue statement.

Forcing works for me, and a hell of a lot of other people here. It's always worth trying, so instead of leaving it out completely, I'd try it out if it were me. Only thing your wasting is a few mouse clicks! No harm in that is there?

For me it's autoserving that is the big problem. Every time I autoserve my modem gets stuck in a reboot loop, but by entering just the filename into the box on the Config File page and leaving the IP blank, I am able to force the higher speed configs.

So in essence, the best thing to do would be to try all ways possible. Don't be afraid to experiment you won't break anything. With your modem in a working state, go to the Backup and Restore link in Haxorware and make a backup of the NonVol memory, then that way if anything goes drastically wrong for you, ie you can't get back online cause you've been experimenting, you can just restore your NonVol from your backup and your modem will be in it's previous state.

FYI, the NonVol memory is as it says, Non Volatile, for example, the data stored on it does not get erased when you power cycle the modem, and it's where all your modems settings are stored when you enter them into Haxorware such as your frequency etc etc etc.

[chef1]

most areas m8

thats correct

[bassethound]

Forcing still working my area