problems with my di1000t - Techwatch Support Forums: Digital & Satellite TV, FTA, Cable, Computers, Mobile Phones, Apple and General Tech Forums

deano81 · 22-08-09, 08:59 AM

hey guys my box boots up then as soon as i get a picture it comes up stop when i un plug it then put it back on i get 4 8's any ideas would be appreciated

yusuf_gaz · 22-08-09, 11:35 AM

Hi

Open up box and take the simm out of its slot and give slot and simm a clean and refit, maybe fitting loosely.

If that dont work then could be the atmels need reflowing.

Regards

deano81 · 22-08-09, 07:03 PM

whats the atmels and how do i reflow them m8

BL4K3Y · 22-08-09, 09:56 PM

If you open the box and look towards the front and left of the power supply, you will see two small chips. You need to heat up each leg on the chips using a soldering iron and some flux so that the solder "reflows" and forms a better solder joint to the pads.

tdubman · 22-08-09, 10:16 PM

could be the atmels on the sim board

yusuf_gaz · 22-08-09, 10:21 PM

Hi

Could be as said above atmels on the main board or the simm, you could do as what blakey has suggested or use a hairdryer and hope you get lucky. If you put in reflowing atmels in the search box should bring up some old posts to give you some more info.

Regards

22-08-09, 08:59 AM	#1 (permalink)
deano81 Junior Member Join Date: Aug 2009 Posts: 3 Thanks: 1 Thanked 0 Times in 0 Posts	problems with my di1000t hey guys my box boots up then as soon as i get a picture it comes up stop when i un plug it then put it back on i get 4 8's any ideas would be appreciated

22-08-09, 11:35 AM	#2 (permalink)
yusuf_gaz Senior Member Join Date: Sep 2008 Posts: 1,964 Thanks: 116 Thanked 623 Times in 525 Posts	Re: problems with my di1000t Hi Open up box and take the simm out of its slot and give slot and simm a clean and refit, maybe fitting loosely. If that dont work then could be the atmels need reflowing. Regards

22-08-09, 07:03 PM	#3 (permalink)
deano81 Junior Member Join Date: Aug 2009 Posts: 3 Thanks: 1 Thanked 0 Times in 0 Posts	Re: problems with my di1000t whats the atmels and how do i reflow them m8

22-08-09, 09:56 PM	#4 (permalink)
BL4K3Y Senior Member Join Date: Apr 2008 Location: Colne, Lancashire Posts: 7,004 Thanks: 247 Thanked 1,319 Times in 1,211 Posts	Re: problems with my di1000t If you open the box and look towards the front and left of the power supply, you will see two small chips. You need to heat up each leg on the chips using a soldering iron and some flux so that the solder "reflows" and forms a better solder joint to the pads.

22-08-09, 10:16 PM	#5 (permalink)
tdubman ipost what iknow not read Join Date: Jul 2008 Posts: 707 Thanks: 66 Thanked 129 Times in 110 Posts	Re: problems with my di1000t could be the atmels on the sim board

22-08-09, 10:21 PM	#6 (permalink)
yusuf_gaz Senior Member Join Date: Sep 2008 Posts: 1,964 Thanks: 116 Thanked 623 Times in 525 Posts	Re: problems with my di1000t Hi Could be as said above atmels on the main board or the simm, you could do as what blakey has suggested or use a hairdryer and hope you get lucky. If you put in reflowing atmels in the search box should bring up some old posts to give you some more info. Regards

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
TalkTalk customers suffering problems	Internet News	Internet	0	13-02-09 11:10 AM
FAO Newbies - Typical dbox 2 problems	kimigonzales	DBox/Dreambox	9	31-01-09 10:31 AM
Signal problems with the new 28/4	chancer	Eurovox	3	20-05-08 10:46 AM
Connection Problems	Realist	Broadband	1	01-04-08 04:32 PM
Fortec Star problems	ukscanking	Satellite Help	21	07-03-07 02:14 PM