pace 4010 pace and nit only - Techwatch Support Forums: Digital & Satellite TV, FTA, Cable, Computers, Mobile Phones, Apple and General Tech Forums

anndy1972 · 27-09-09, 02:04 PM

Hi guys is this another one for the bin the box goes pace then nit then back to pace and so on . It did fire up last night after doing this for a while but back to broke again this morning . I pulled the red jumper an hour or so ago and now it just says pace .

cheers
Andy

scott27 · 27-09-09, 02:08 PM

check nthell/vm have`nt cut your feed from the big bad green boxes..lol.

scott

reddiesel · 27-09-09, 02:11 PM

Check your cable connection , f connecters etc, could be just poor signal.

anndy1972 · 27-09-09, 02:12 PM

Cable feed is fine guys

reddiesel · 27-09-09, 02:21 PM

Another thing to check is the inner connector on the box where the cable screws in, sometimes they break off the board if theyve been overtightened, check the capacitors in box also.

lucus · 27-09-09, 02:23 PM

does it keep rebooting and trying to update cus had that same problem ended up chucking it away cus whatever i done couldnt get anything out of it, libby wouldnt connect was dead.
regards

G77 · 27-09-09, 02:31 PM

how many atmels on the board and where are you using it?

anndy1972 · 27-09-09, 03:18 PM

im using the box in pure and there is 1 broadcom chip on it box does the same anywhere i plug it in at but the feed is deffo good before i pulled the jumper it would let me go in to em for a sec now it wont

adjbeatbox · 27-09-09, 03:22 PM

Like G77 said how many Atmel chips is there @ the front of the box?? should be either 2 or 4?
Cause, this sounds like 1 of them needing reflowed
Beatbox

G77 · 27-09-09, 03:37 PM

nah, should be one or two. one is for pure two for telepest (i think)

27-09-09, 02:04 PM	#1 (permalink)
anndy1972 Senior Member Join Date: Apr 2008 Location: pure Posts: 551 Thanks: 137 Thanked 38 Times in 36 Posts	pace 4010 pace and nit only Hi guys is this another one for the bin the box goes pace then nit then back to pace and so on . It did fire up last night after doing this for a while but back to broke again this morning . I pulled the red jumper an hour or so ago and now it just says pace . cheers Andy

27-09-09, 02:08 PM	#2 (permalink)
scott27 Member Join Date: Jun 2008 Location: glesga Posts: 65 Thanks: 1 Thanked 3 Times in 3 Posts	Re: pace 4010 pace and nit only check nthell/vm have`nt cut your feed from the big bad green boxes..lol. scott

27-09-09, 02:11 PM	#3 (permalink)
reddiesel Super Moderator Join Date: May 2007 Location: Beds Posts: 5,708 Thanks: 176 Thanked 957 Times in 839 Posts	Re: pace 4010 pace and nit only Check your cable connection , f connecters etc, could be just poor signal. __________________

27-09-09, 02:12 PM	#4 (permalink)
anndy1972 Senior Member Join Date: Apr 2008 Location: pure Posts: 551 Thanks: 137 Thanked 38 Times in 36 Posts	Re: pace 4010 pace and nit only Cable feed is fine guys

27-09-09, 02:21 PM	#5 (permalink)
reddiesel Super Moderator Join Date: May 2007 Location: Beds Posts: 5,708 Thanks: 176 Thanked 957 Times in 839 Posts	Re: pace 4010 pace and nit only Another thing to check is the inner connector on the box where the cable screws in, sometimes they break off the board if theyve been overtightened, check the capacitors in box also. __________________

27-09-09, 02:23 PM	#6 (permalink)
lucus Senior Member Join Date: Jul 2009 Location: TW Posts: 408 Thanks: 80 Thanked 74 Times in 65 Posts	Re: pace 4010 pace and nit only does it keep rebooting and trying to update cus had that same problem ended up chucking it away cus whatever i done couldnt get anything out of it, libby wouldnt connect was dead. regards

27-09-09, 02:31 PM	#7 (permalink)
G77 Super Moderator Join Date: May 2008 Posts: 6,118 Thanks: 695 Thanked 1,250 Times in 1,044 Posts	Re: pace 4010 pace and nit only how many atmels on the board and where are you using it? __________________ 1M Motorised Dish, 45W-36E, DM800HD. Quad LNB Mesh Mini Dish, 28.2E, DM500, TM500. Samsung Galaxy S GT-I9000 XXJVU & CF-Root.

27-09-09, 03:18 PM	#8 (permalink)
anndy1972 Senior Member Join Date: Apr 2008 Location: pure Posts: 551 Thanks: 137 Thanked 38 Times in 36 Posts	Re: pace 4010 pace and nit only im using the box in pure and there is 1 broadcom chip on it box does the same anywhere i plug it in at but the feed is deffo good before i pulled the jumper it would let me go in to em for a sec now it wont

27-09-09, 03:22 PM	#9 (permalink)
adjbeatbox Multimedia Menace Join Date: Aug 2007 Posts: 403 Thanks: 46 Thanked 74 Times in 62 Posts	Re: pace 4010 pace and nit only Like G77 said how many Atmel chips is there @ the front of the box?? should be either 2 or 4? Cause, this sounds like 1 of them needing reflowed Beatbox __________________ All information given is Hypothetical & for Educational purposes ONLY, Have A Nice Day...

27-09-09, 03:37 PM	#10 (permalink)
G77 Super Moderator Join Date: May 2008 Posts: 6,118 Thanks: 695 Thanked 1,250 Times in 1,044 Posts	Re: pace 4010 pace and nit only nah, should be one or two. one is for pure two for telepest (i think) __________________ 1M Motorised Dish, 45W-36E, DM800HD. Quad LNB Mesh Mini Dish, 28.2E, DM500, TM500. Samsung Galaxy S GT-I9000 XXJVU & CF-Root.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
pace 4010 jtag connection trouble!!	anthrax	Cable TV Chat	10	26-03-10 12:37 AM
Pace 4001 NC can't access engineering menu / stuck in tune / nit	nexatron	Cable TV Chat	5	08-08-09 09:43 AM
Pace DITV 2000	abbs2002	Cable TV Chat	1	25-05-09 11:02 AM
Pace D4000 Error Messages	mk753	Other Cable Boxes	7	16-04-09 10:32 PM
pace DI4010-N stuck on nit	llsarahll	Other Cable Boxes	1	05-01-09 10:25 PM