haxoware tut needed

[haggar]

hi,please can some one tell me where am i going wrong.im using jtag to flash 5101e.ive write all the original 5101,then i write the haxoware 1.1r34,it says successful but come to open the haxoware page with the 192.168 etc its can not open page.ive gone to the net connections put in
192.168.100.10 ip,255,255 mask,192.168.100.1 for the gateway but still no good.i am new to this game but i av read an read alot of posts an still none wiser.so please can some one with the knowledge help me get this f##kin haxoware page plzzzzzzzzzz

[fnr3master]

wot you flashing with scwarts or toms and wots the size of the dump you putting on there

[BL4K3Y]

Flash a 2MB Haxorware dump (if you aren't already doing so). I also found that erasing the chip first helped it to write better. I used the Schwartzekatze software to do mine .

[haggar]

im using schwartz,i use the 2mb 5101e full dump first then im using haxoware.blakey 8 how do i erase chip first ?.thanks

[chrissy2k6]

Originally Posted by blakey_8

I also found that erasing the chip first helped it to write better. I used the Schwartzekatze software to do mine .

How did you 'erase' the chip???...I can't flash mine cos of verification errors but wiping the chip might help!

[haggar]

does flashing with 5101e orignal dump file count for erasing the chip,because im new to this game too,another thing is which chip you using cos the dump file i got works with intel chip but not with a st chip.i only know this because my mate came over and shown me so much before he had to go.the problem i got is -i done the flash but i cant open the haxoware page!

[fnr3master]

m8 you kind of going around in circles here.
best thing to do flash ur stock firmware on it and then check if u get the 192.168....... page and it should be the surfboard page you get once you done that proceed to flash with haxoware.

go to haxoware site download the latest haxoware flash which is rev39 there are 2 flashes in there the one you want is the lite version.

then get tom jtag utilty 1.3, and on the jtag tab where it says blackcat lpt click open next to it then click on the console tab. and in the lower text box type detect, then it will show you ur chip info.

once it has detected you chip these are the commands to flash it

ldram image0 (press enter and then select you haxo file you want to flash in ur case rev39.

program image0 (press enter it will write to this sector)

program image1 (press enter it will write again)

once its all done power off and connect up and enter 192.168 page and u should have haxo, then just enter all you correct values etc and all is good.

note: you can click on options in toms jtag utilty and tick or untick verify data.
if you click on main you can also detect the chip that way aswell.

[haggar]

fnr3master m8,ive done what you said but still i cant access the 192.168 page .i downloaded jtag utility 1.3 did what you said, everything was completed .the thing im not sure ive done right was that i flashed the original dump on it first,but it said completed so i thought it was ok.can you tell me what lights should be on when starting the flash

[fnr3master]

if you cant access the 192.page of haxoware, try manually setting ur nic card etc and see if that works, but then dont forget to set it back to obtain automaticlly afterwards.

also wot you should of done is put the original stock dump back on and checked it by trying to access the 192.168....page and see if it went into the surfboard page.

if it did then you should of carryied on with the haxo install/flash.

let me know how u get on i will try and assit you some more

[haggar]

thanks for the reply, going to have a try now.thanks again m8