How to for Sammy DSR 9500 VIA CI with Revolution Gold Emu 4.x by MAHDI!

[gorski]

If you have problems maybe uploading the new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well, kill your Sammy at the back and then... Here's a copy of my post from other threads:

When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.

Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.

If it times-out - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!

Choose the EMU you want to upload. Then Settings list. Then RAM. Then CAID list.

Enjoy! Hopefully!

HyperTerminal explanations [thanx to Papagen!!]:

Uploading Software Into Samsung Using Hyper Terminal

Start/Program/Accessories/Communications/Hyper Terminal

Setting the Hyper Terminal

1. Start Hyper Terminal.
2. In the field "Name" write for example Samsung 9500, choose an icon and click OK.
3. In the new opened window, near "Connect using" choose "Direct to COM1, afterwards click OK.

Port Settings

1. Bits per second : 115200
2. Data Bit : 8
3. Parity : NONE
4. Stop Bit : 1
5. Flow Control : Hardware
Click OK

Uploading software into Hyper Terminal

1. Choose TRANSFER
2. Then choose SEND FILE ....
3. BROWSE - select from hard drive the desired version of software (e.g. DSR9500_Eurocam_5-1_EMU_vXX.bin)
4. Choose 1KXmodem for Protocol
Don't press the button "Send", you will do it subsequently.

After you have done the procedure described, connect your computer with Samsung using a RS232 connection cable.
Before you start uploading the new software into Samsung I would advise you to firstly remove all the cams or cards from it (if any are inside).

The things you have to do are :
1. Disconnect your Samsung using the switch on the rear.
2. In the front of Samsung keep pressed the "right arrow" (volume up).
3. Power up your Samsung on the rear switch and keep constantly pressed "right arrow" (volume up).
Keep the "arrow" pressed until the "3-01" appears on the display,
from that moment the computer will show "............................... Loading"
4. In that moment, in the Hyper Terminal, click the button "Send" (you have about 15 seconds to perform that operation).
With clicking on "Send" starts the uploading the software into Samsung.
Don't be hasty! Wait for entire process to terminate.
Process is terminated when on the Samsung a clock appears.
Afterwards insert some of the cards with Conax emulation without keys.
That was it.

If you have done all properly, there is a desired version of software in you Samsung.
The easiest way to verify if upload succeeded : Menu/System properties/System information.
Old versions of the EMU software has the version number 118 and new have 133.

[gorski]

1) Samsung DSR 9500 VIA CI [HW 504, Loader 500 or 501] on Standby

2) Connect to the PC via straight serial cable

3) Start Samsung DSR Studio 1.2 Editor by MAHDI

4) Choose FW Loader TAB

5) Choose Serial Port

6) Click on Send FW and then choose which EMU [4.3 at this point - and it's away, racing...]

7) Wait untill you see the clock on Sammy Display

8) Start Sammy [on FTA channel, just in case], check it, then put it on Standby

9) Click on RAM Editor Tab in the Samsung DSR 9500 Studio Editor by MAHDI

10) Choose Serial Port, then Open File, then click on Write and wait for the clock again

11) You'll see "Insert smartcard" message, then re-start Sammy

12) tps.bin click on Files -> Open Files -> choose the fresh t*s.bin -> when "Ready for Upload" appears -> click on Send -> wait for the clock to appear -> put Sammy to Stand By and switch ON again.

13) At this point I would [and I am going to]
Menu -> Channel organising -> Delete all channels and then
Menu -> Installation -> Manual Scanning and do your own settings list, just so everything is working as it should...

14) Experiment with various cards, depending on which ones one has...

15) Sort out the GBox and Card Sharing bits...

THANKING YOOOOOUUUUUUUUUUUUUUUUUUUUUUU!!!!!!!!!!!!!!!

MAHDI FOR PRESIDENT!!!

[gorski]

In Gold Emu 4.x you have this as an option:

Press 0 and then Menu and you get into the main Emulator Menu.

At the bottom you have Key Editor Menu -> choose a coding system 0 -> Ident -> key you wanna change by using this scheme:

0 = 0 Button

1 = 1 Button

2 = 2 Button

3 = 3 Button

4 = 4 Button

5 = 5 Button

6 = 6 Button

7 = 7 Button

8 = 8 Button

9 = 9 Button

A = PG+ Button

B = PG- Button

C = GREEN Button

D = YELLOW Button

E = BLUE Button

F = RED Button

Del = LAST Button

Thanx to Dalen, my translation and a small edit...

How to change a key via Remote...

1. Choose a channel to check if the key is OK

2. Get into the receiver's Gold Emu Menu (press 0 + Menu on your Remote)

3. Choose the Key Editor Menu

4. Choose a system of encryption (like Nagra for D+)

5. Choose the right IDENT (for D+ it's 4101)

6. When you choose the right one press on the OK button

7. In the window for putting the key in first
7a. we write the IDENT, then
7b. the INDEX and then
7c. the first 16 signs

8. Repeat all that and put in the next 16 signs

9. If it's all cool the pictuire should appear... colours!!!

10. Press on Exit button

An example of changing a key 00 for D+ (Nagra)
410100CE5823E424584566
410101F6152652E52BE556

Then the 01 key for D+ (Nagra)
410102CE5823E424584566
410103F6152652E52BE556

These keys are just an example and do not open anything!

My addition: D+ overall uses keys 00 and 01.
The 00 key in Samsung uses key places 00 and 01.
The 01 key in Samsung uses key places 02 and 03.

With the new EMU 4.3 we have the same procedure but with a minor change: we need to press EXIT for each key, once we're finished:

For instance:

410100xxxxxxxxxxxxxxxx -> EXIT

Here the EMU returns automatically to the beginning and puts the key in. Then we repeat the procedure...

410101xxxxxxxxxxxxxxxx -> press the EXIT button on your Remote again and voila!! The key is in!!!

:lightbulb: :thumbs_up:

Niiiiiiiiiiiiiiiiiceeee!!!!:tounge_smile:

[soft2730@otenet.gr]

i'm new in forum how often d+ change keys?

[Begood]

hi,
it's difficult to tell,but it can every day. You can find a file uptaded on this forum.

Bye

[gorski]

HOW TO PROGRAMME YOUR SAMMY
including VIACI, CI, FTA and EMVIA versions

0) One must have Loader 500 or 501 in one's machine [See your basic Settings in the Menu to check it], in order to programme it via a serial 9-pin cable.

If it doesn't work, one must use JTAG to put the Loader 500/501 in, then do the Emu via the serial cable.

Do not hurry, do not cut corners, if you want it all to work properly!

1) Connect Sammy with your PC/laptop
-for an older PC one needs only a serial cable, as chances are it has the serial [9 pin] port
-for a newer PC, if it has no serial but only a USB port, first connect your straight serial 9-pin cable into Sammy, plugging the other end of the cable into a "serial/USB" cable adaptor, so one can plug the other end of the adaptor into the USB port of your PC/laptop

2) Download the following, freshest files to your PC/laptop:
-EMU [the latest Emu is v. 8.4.]
-Tools
-Settings list
-RAM.bin
Unpack them to your PC/lappy, to their respective folders.

The programming itself

3) Switch off the receiver at the back, for 10-20 seconds, then turn it back on again.

4) Start STUDIO 1.5.1 by Maestro MAHDI (choose the right port, for instance COM1 or USB1 or whatever it is in your setup)
-click on DSR FW Loader, then
-Send FW, then
-choose the Emu you want to programme (the latest now is SamsungDSR9500_RVGOLD_V8.4) and then
-Open -> to programme the EMU.
One will see the progress on the LED or maybe on the TV screen, if one is connected to the TV.
WAIT for the CLOCK on Sammy display - do NOT hurry!!!

When it's finished, put the channels list in, using, for instance, Semco Editor.

Btw, SetEdit 1.12 exists, too. It does the job, too!

Receiver must be in Standby mode (using your remote control).

5) Start the Semco Editor (the right port should be chosen, for instance COM1 or USB1), then
-go to File in the upper left corner, then
-to Open
-a new window will appear, to choose a list on your PC (format "something.sdb"), then
-click on Open
-when Semco Editor opens it, click on the Load Data Base From PC To Set Top Box icon.

Wait.

When it is done, quickly do the Emu reset [one must be connected to the TV to see the options], which one does only once now, after programming the Emu:

6) Start Sammy from Standby using your remote and execute RESET OF EMU:
-press 0 + Menu on your remote, quickly, one after the other, then
-choose RESET TO EMU DEFAULTS and
-press OK on your remote.

Sammy should switch itself off now. Start Sammy from Standby using the remote.

{After it resets, you can go back to EMU MENU to make sure you have the following configuration:

EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD

...or simply play with whatever Sammy has in RG 8.4 }

[Oh, by the way: sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!]

Now, let's put RAM.bin in [it contains the keys to open the hacked channels...]

7) Sammy is in Standby mode
-Start Samsung DSR Studio 1.5.1 -> choose Ram Editor modus (a special TAB).
-Click on Open File and find the latest RAM.bin on your PC/laptop
-If "Empty Write" is ticked/chosen - remove it.
-Click on Write and wait for "End Write"

Startaj Sammy and watch...

============BY THE WAY+++++++++++++

How to put the keys via remote in

Go to a coded channel and press 0, then Menu [as above] to open the EMU Menu.

At the bottom of the list you'll see Key Editor Menu -> choose a coding system -> Ident -> key one wants to edit.

The scheme is as follows:
0 = 0 Button
1 = 1 Button
2 = 2 Button
3 = 3 Button
4 = 4 Button
5 = 5 Button
6 = 6 Button
7 = 7 Button
8 = 8 Button
9 = 9 Button
A = PG+ Button
B = PG- Button
C = GREEN Button
D = YELLOW Button
E = BLUE Button
F = RED Button
Del = LAST Button

An example (thanx to Dalen)

With little arrows choose IDENT (i.e. 4101 for D+)
Press OK button
In window Key write : IDENT and INDEX and first 16 Keys
In window Key write : IDENT and INDEX and second 16 Keys
Press Exit button

In example to change Keys 00 for D+ (N*gra)
410100CE5823E424584566 - 410101F6152652E52BE556

In example to change Keys 01 for D+ (N*gra)
410102CE5823E424584566 - 410103F6152652E52BE556

These keys are not valid, they are just an example.

=====================================

Newer EMU Gold 4.3 has more places/digits to put in.

The procedure is the same, except that one needs to press the EXIT button when finished:

410100xxxxxxxxxxxxxxxx -> EXIT takes you automatically back, having written the key in and the again

410101xxxxxxxxxxxxxxxx -> EXIT and that's it!

===========================================

Thanx to Cruiser:

How to enter BISS keys to RevGold4.0

*Press twice i button to get SIِِD and 2 last byte of PMT and PCR;
Example: FOX tv Serbia SID:377D PMT:A4 PCR:A5
**Now You need keys;
Example: FOX tv Serbia:XXXXXXXXXXXX

1)switch to one of BISS channels(like FOX tv Serbia)
2)go to the keys menu by pressing:
(Button 0 + Menu Button)>Key Editor Menu>BISS & DCW
3) press OK button
4)now you have to enter first SID(377D) then 2 last byte of PMT(A4) then 2 last byte of PCR(A5) and then the right keys(XXXXXXXXXXXX) and after all enter FFFF.(I have to mentioned the keys I've wrote in above is only for FOX tv Serbia for other channels you have to change the D*gits)
You have to see the picture.

How to enter BISS keys to RevGold4.2

*Press twice i button to get 2 last byte of SID,PMT,VID and AID;
Example: FOX tv Serbia SID:7D PMT:A4 PCR:A5 VID:A5 AID:A6
**Now You need keys;
Example: FOX tv Serbia:XXXXXXXXXXXX

1)switch to one of BISS channels(like FOX tv Serbia)
2)go to the keys menu by pressing:
(Button 0 + Menu Button)>Key Editor Menu>BISS & DCW
3) press OK button
4)now you have to enter first 2 last byte of VID(A5) then AID(A6) then SID(7D) then PMT(A4) and then the right keys(XXXXXXXXXXXX) and after all enter FFFF.(I have to mentioned the keys I've wrote in above is only for FOX tv Serbia for other channels you have to change the D*gits)
You have to see the picture.
enjoy/thanx MAHDI/HSH

Thanx to Maumixio, how to enter a DCW:

Goto InXtc channel and press twice "i" button and take note of following infos:

Hotbird freq 10853
SID 21AD
PMT 0096

Calculate frequency in HEX 2A65

pick up 3° and 4° byte of SID e PMT

keep public key (demo) 1234567890ABCDEFFEDCBA0987654321 and take note that only colored byte are important
At last our working key shoul be done by remote and Studio 1.3
2A65 AD96 FEDCBA876543
See example attached. Enjoy, Maumixio.

[gorski]

===========================================

Thanx to Cruiser for the list of channels which can be seen using Sammy's Emu and RAM.bin file/keys:

N*gra:
DigiTV 1°W ok key 00-17.06.09.
Tv Globo 13°E ok
Multicanal 30°W

Seca:
RAI 13°E- ok next key 0D July
Mediatech 4°W- ok next key 0D July

Cryptoworks:
Kingston 5°E
Jetix 13° 10723/H/29900
Cartoon Network & TNT Germany ok 9°E 11728/V/27500

Viaccess:
Mezzo 13°E 12245/H/27500
SIC Int. 16°E 12568/H/3703
MCM Belgique 5°W 12543/H/27500

Biss Channel:
12149 TVE 1 30°W;
11931 LDTV 30°W;
12149 TVM 2 30°W;
12092 AXN PORTUGAL 30°W;
11474 TV CANARIA 30°W;
12735 ENTV 15°W;
11177 FOX TV 12,5°W;
11373 TOUCH TV 12,5°W;
11188 FOX GERMANY 12,5°W;
11066 Fox Sport 8°W; new PMT
11066 Discovery 8°W;
11066 Fox news 8°W;
12583 2M 12,5°W;
11423 AL RIYADIAH 7°W;
11065 Canal 6 Feed 5°W
11065 ENTV 5°W
12543 FOX LIFE 5°W;
10722 MEGASPORT 4°W;
10722 TV KYIV 4°W;
10722 1PLUS1 4°W;
10759 Qtv 4°W;
11766 TET 5°E;
12073 OCK 5°E;
11823 S2K (Sat 2000) 9°E;
11296 S2K (Sat 2000) 13°E;
12673 TVM MAROC 13°E;
11643 MBC US 26°E;
12608 IMED 42°E;
11894 Ans TV 42°E
11178 Ekin Turk TV (USUK TV) 42°E;
12678 24 42°E;
12593 RUSTAVI 2 42°E;
11054 NTV SPOR 42°E;
11607 AZERBAYCAN TV 42°E;
11870 TV8 42°E;
12605 Georgian TV - 42°E;
11044 STS 53°E;
11044 STS 53°E;
11044 TELEKANAL 53°E;
11161 STOLICNOE TV 53°E;
11044 Nash Dom 53°E

==================================================

How the AU function for DigiTV [if it still functions, by the time you read this]

(Firstly, I do not know EXACTLY nowadays how and IF it functions, as I gave my Sammy away, so you must play with it a bit to see what works... Now...)

Go to a channel in DigiTV package, then do the following...

Go to EMU Menu, where you should have:

EMU - ON
EMM - ON
CAID Mode - AUTO
CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]

I hope you'll soon have the pretty colours...

In addition: do NOT reset the EMU every time you want a provider to AU!!!

Do it just once, after the installation!

Then put the RAM.bin in...

Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...

Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!

==========IN CASE OF TROUBLE===========

If your Sammy must be flashed with a new SW from scratch/zero/from the beginning, as it were - but your screen is black and it keeps giving you these numbers in the display [I had this problem!: 6-01 changing to 6-03 then]:

Kill your Sammy at the back for a few minutes and then...:

When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.

If you do not manage the first time - keep trying until you get it right...

But!

Before you do any of that you must make sure you have Sammy connected to a PC via a serial cable and your HyperTerminal prepared, as Papagen already described beautifully:

On your PC: Start/Program/Accessories/Communications/Hyper Terminal

Setting the Hyper Terminal

1. Start Hyper Terminal.
2. In the field "Name" write for example Samsung 9500, choose an icon and click OK.
3. In the new opened window, near "Connect using" choose "Direct to COM1, afterwards click OK.

Port Settings

1. Bits per second : 115200
2. Data Bit : 8
3. Parity : NONE
4. Stop Bit : 1
5. Flow Control : Hardware
Click OK

Uploading software using Hyper Terminal

1. Choose TRANSFER
2. Then choose SEND FILE ....
3. BROWSE - select from hard drive the desired version of software (e.g. DSR9500_Eurocam_5-1_EMU_vXX.bin)
4. Choose 1KXmodem for Protocol
Don't press the button "Send", you will do it subsequently.

After you have done the procedure described, connect your computer with Samsung using a RS232 connection cable.
Before you start uploading the new software into Samsung I would advise you to firstly remove all the cams or cards from it (if any are inside).

The things you have to do are :
1. Disconnect your Samsung using the switch on the rear.
2. In the front of Samsung keep pressed the "right arrow" (volume up).
3. Power up your Samsung on the rear switch and keep constantly pressed "right arrow" (volume up).
Keep the "arrow" pressed until the "3-01" appears on the display,
from that moment the computer will show "............................... Loading"
4. In that moment, in the Hyper Terminal, click the button "Send" (you have about 15 seconds to perform that operation).
With clicking on "Send" starts the uploading the software into Samsung.
Don't be hasty! Wait for entire process to terminate.
Process is terminated when on the Samsung a clock appears.
That was it.

Or another possibility:

If you have problems uploading a new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well,

1) kill your Sammy at the back and then...

2) when you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.

3) Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.

If it times-out [in both cases] - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!:thumbs_up:

GREAT JOB, MAHDI [& co.]!!!:wink_smile::regular_smile: