HOW TO PROGRAMME YOUR Samsung 9500 - Techwatch Support Forums: Digital & Satellite TV, FTA, Cable, Computers, Mobile Phones, Apple and General Tech Forums

oys · 20-07-08, 07:39 PM

HOW TO PROGRAMME YOUR Samsung 9500

Switch your Sammy off at the back BEFORE you program the EMU in!

After Sammy has cooled down a bit [say 2-3 minutes] switch it on at the back and keep it on Standby.

Now start the STUDIO 1.2 [or 1.3] by Maestro MAHDI and go to DSR FW Loader and Send FW, then choose the Emu [now 8.0] and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush!

NOW PUT THE RAM.bin IN

Now put your Sammy to Standby, and then put the RAM.bin file [with all the other keys] in [oys or Cruiser ], then start your Sammy via remote. All working fine .

HOW TO GET YOUR AU TO WORK

Using your remote, start your Sammy from Standby and do a RESET OF EMU by pressing 0 + Menu on your remote, quickly in succession! Then go down to RESET TO EMU DEFAULTS and press the OK button on your remote.

Sammy will switch itself off now. Use your remote to start it from Standby.

Go to the EMU MENU [by pressing 0 + Menu in quick succession] and you will see the following configuration:

EMU - ON
EMM - ON

Sharing Mode - HSIC - that's for Humax CS [change to the protocol you need, when using CS; SSSP DSR for GBox and

DSR for Sammy original]

DCW Delay - experiment to see which setting here gets you a better result
RS232 Delay - as above, see which setting here gets you a better result

Digi Tv , Polsat and Premere

Here I couldn't get the picture, that is to say the AU on Premiere, Polsat and Digi Tv to work for me, so I changed the channel and it still didn't work. So, I put the receiver to Standby via Remote [do not kill it at the back - no need for that any more!], then I switched it back on immediately - and the picture came very quickly!!! Maybe I just didn't wait for long enough? Anyway, the AU is working nicely!

GREAT JOB, MAHDI !

oys · 20-07-08, 07:41 PM

If you have visited this section of our forum means you are happy

Owner Samsung DSR 9500.

There are some versions of a given receiver,
Depending on marks and established FW it provides viewing
The coded channels using various codings.

DSR 9500EM VIA : 2 Smart Card Readers for Viaccess Embedded

DSR 9500VIA CI : 2 Smart Card Readers for Viaccess Embedded + 2CI Slots

DSR 9500AY: 2 Smart Card Readers for Viaccess,ConaxEmbedded + 2CI Slots

DSR 9500A EM VIA; 2 Smart Card Readers for Viaccess Embedded

DSR 9500AX 2 Smart Card Readers for Viaccess,ConaxEmbedded

DSR 9500AZ; 2 Smart Card Readers forConax Embedded + 2CI Slots

DSR 9500Z : 2 Smart Card Readers for Conax Embedded + 2CI Slots

DSR 9500AR : 2 Smart Card Readers for Irdeto Embedded + 2CI Slots

DSR 9500AT : 2 Smart Card Readers for Cryptoworks Embedded + 2 CI Slots

The most successful for the consumer as it is not strange, appeared earlier versions from this series it DSR 9500 EM VIA and DSR 9500 VIA CI (has advantage as is the opportunity to use modules CAM)

The most suitable variant FW For them 118 version of a software + EMU.

P.S. At present EMU on the basis of 118 software it is not supported any more. At the moment EMU it is based on 133 software, the founder has christened it as Sammy Revolution.

DSR 9500 A EM VIA at first sight differs nothing from DSR 9500 EM VIA but the ill-A letter And which costs after 9500 does not give an opportunity to fill EMU,

I shall not explain why as all the same at you it will turn out nothing, better at once refuse this invention.
The most optimum variant for this version to alter it in DSR 9500AY it will provide viewing the coded channels prophesying in Viaccess, Seca, Nagra, Betacrypt, Conax with use of cards proembroidered under Conax xin1.

To change the version in DSR 9500 A EM VIA it is possible only with help http://www.anonym.to/?http://forum.metabox.ru/attachment.php?attachmentid=1077&d=1159000916]Jtag[/URL] at presence full дампа
For versions DSR 9500 EM VIA and DSR 9500 VIA CI if they not patch for first time too it is required Jtag for change of the loader with 504; 505 on 500; 501 then it will be possible to change п.о through COM port.
Under the following references you can download all necessary instructions, programs and files.

manual for loading FW

RS - 232

20-07-08, 07:39 PM	#1 (permalink)
oys Member Join Date: Jan 2008 Posts: 47 Thanks: 0 Thanked 0 Times in 0 Posts	HOW TO PROGRAMME YOUR Samsung 9500 HOW TO PROGRAMME YOUR Samsung 9500 Switch your Sammy off at the back BEFORE you program the EMU in! After Sammy has cooled down a bit [say 2-3 minutes] switch it on at the back and keep it on Standby. Now start the STUDIO 1.2 [or 1.3] by Maestro MAHDI and go to DSR FW Loader and Send FW, then choose the Emu [now 8.0] and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush! NOW PUT THE RAM.bin IN Now put your Sammy to Standby, and then put the RAM.bin file [with all the other keys] in [oys or Cruiser ], then start your Sammy via remote. All working fine . HOW TO GET YOUR AU TO WORK Using your remote, start your Sammy from Standby and do a RESET OF EMU by pressing 0 + Menu on your remote, quickly in succession! Then go down to RESET TO EMU DEFAULTS and press the OK button on your remote. Sammy will switch itself off now. Use your remote to start it from Standby. Go to the EMU MENU [by pressing 0 + Menu in quick succession] and you will see the following configuration: EMU - ON EMM - ON Sharing Mode - HSIC - that's for Humax CS [change to the protocol you need, when using CS; SSSP DSR for GBox and DSR for Sammy original] DCW Delay - experiment to see which setting here gets you a better result RS232 Delay - as above, see which setting here gets you a better result Digi Tv , Polsat and Premere Here I couldn't get the picture, that is to say the AU on Premiere, Polsat and Digi Tv to work for me, so I changed the channel and it still didn't work. So, I put the receiver to Standby via Remote [do not kill it at the back - no need for that any more!], then I switched it back on immediately - and the picture came very quickly!!! Maybe I just didn't wait for long enough? Anyway, the AU is working nicely! GREAT JOB, MAHDI !

20-07-08, 07:41 PM	#2 (permalink)
oys Member Join Date: Jan 2008 Posts: 47 Thanks: 0 Thanked 0 Times in 0 Posts	HOW TO PROGRAMME YOUR Samsung 9500 If you have visited this section of our forum means you are happy Owner Samsung DSR 9500. There are some versions of a given receiver, Depending on marks and established FW it provides viewing The coded channels using various codings. DSR 9500EM VIA : 2 Smart Card Readers for Viaccess Embedded DSR 9500VIA CI : 2 Smart Card Readers for Viaccess Embedded + 2CI Slots DSR 9500AY: 2 Smart Card Readers for Viaccess,ConaxEmbedded + 2CI Slots DSR 9500A EM VIA; 2 Smart Card Readers for Viaccess Embedded DSR 9500AX 2 Smart Card Readers for Viaccess,ConaxEmbedded DSR 9500AZ; 2 Smart Card Readers forConax Embedded + 2CI Slots DSR 9500Z : 2 Smart Card Readers for Conax Embedded + 2CI Slots DSR 9500AR : 2 Smart Card Readers for Irdeto Embedded + 2CI Slots DSR 9500AT : 2 Smart Card Readers for Cryptoworks Embedded + 2 CI Slots The most successful for the consumer as it is not strange, appeared earlier versions from this series it DSR 9500 EM VIA and DSR 9500 VIA CI (has advantage as is the opportunity to use modules CAM) The most suitable variant FW For them 118 version of a software + EMU. P.S. At present EMU on the basis of 118 software it is not supported any more. At the moment EMU it is based on 133 software, the founder has christened it as Sammy Revolution. DSR 9500 A EM VIA at first sight differs nothing from DSR 9500 EM VIA but the ill-A letter And which costs after 9500 does not give an opportunity to fill EMU, I shall not explain why as all the same at you it will turn out nothing, better at once refuse this invention. The most optimum variant for this version to alter it in DSR 9500AY it will provide viewing the coded channels prophesying in Viaccess, Seca, Nagra, Betacrypt, Conax with use of cards proembroidered under Conax xin1. To change the version in DSR 9500 A EM VIA it is possible only with help http://www.anonym.to/?http://forum.metabox.ru/attachment.php?attachmentid=1077&d=1159000916]Jtag[/URL] at presence full дампа For versions DSR 9500 EM VIA and DSR 9500 VIA CI if they not patch for first time too it is required Jtag for change of the loader with 504; 505 on 500; 501 then it will be possible to change п.о through COM port. Under the following references you can download all necessary instructions, programs and files. manual for loading FW RS - 232